中文内容展开
推荐将白蜡机与其他温度控制系统保持一定距离。
不要将气流直接吹向白蜡机和所在位置。包括空调（挂式，立式，中央空调）、风扇、取暖器（空间加热或其他）。
· 不可将白蜡机暴露在阳光和紫外线直射环境
· 不可将白蜡机放置在门口附近
· 将白蜡机和氧气机远离水源，例如水槽、浴缸、超声波清洗机等
· 不可将白蜡机放到其他运行设备旁（如抛光机、注蜡机、紫腊机）
· 避免环境大幅度温度变化
确保室温在以下范围内：
· 最低温度为22℃（72℉）
· 最高温度为28℃（82℉）
重要提示：湿度请保持在45%以下。
白蜡机空气环境相关建议
白蜡机应在清洁的空气环境中使用。空气中的高浓度杂质可能会混入材料和打印的工件里，还会影响制氧机使用寿命。
· 房间必须有一定的空气流动（最低每分钟0.03平方米）来保证白蜡机产生的热量足以散发出去
· 空调出风口应距离打印机至少3米，且风向不会直接对准白蜡机
白蜡机的工作环境请确保没有以下严重影响因素：
· 尘埃
· 烟雾
· 蒸汽
白蜡机操作摆放空间参考
安装空间规范
白蜡机必须放置在确保稳定坚固、平整平稳的平台上：
白蜡机最低限度的使用、维护和散热空间：
-
打印机后方至少35厘米（13.78英寸）
-
打印机左右两侧至少60厘米（23.62英寸）
-
摆放设备台面上方至少120厘米（47.24英寸）
氧气机工作空间要求：
-
可以放置在白蜡机附近的地面上，通过气管连接到白蜡机。
-
氧气机前后左右至少有20厘米进出气以及散热空间确保稳定供氧。
白蜡机电气要求
在供电不稳定的情况下，推荐配置UPS（不间断电源）来保护白蜡机。
确保白蜡机稳定运行，必须满足以下所有电气要求：
1. 正常市电标准供电
2. 不要将任何额外的设备接入电源电路
3. 白蜡机需要220V电压，电流不少于8A
4. 氧气机需要220V电压，电流不少于5A
5.将白蜡机和氧气机分别接入单独的浪涌防雷保护器或UPS
English is HERE!
General Environment Requirements
-
System Isolation: It is recommended to maintain a certain distance between the White Wax machine and other temperature control systems.
-
Airflow Management: Do not direct airflow from air conditioners (wall-mounted, floor-standing, or central), fans, or heaters toward the machine or its installation site.
-
Light Exposure: Do not expose the machine to direct sunlight or ultraviolet (UV) radiation.
-
Placement Safety: * Avoid placing the machine near doorways.
-
Keep the printer and oxygen generator away from water sources, such as sinks, bathtubs, and ultrasonic cleaners.
-
Do not place the machine next to other operating equipment, such as polishing machines, wax injectors, or purple wax machines.
-
-
Stability: Avoid environments with drastic temperature fluctuations.
Temperature and Humidity Specifications
Ensure the room temperature remains within the following range:
-
Minimum Temperature: 22°C (72°F).
-
Maximum Temperature: 28°C (82°F).
-
Humidity (Important): Maintain humidity levels below 45%.
Air Quality and Ventilation Recommendations
The White Wax machine must be operated in a clean-air environment. High concentrations of impurities in the air can contaminate the materials and printed parts, and may also reduce the lifespan of the oxygen generator.
-
Ventilation: The room must have adequate airflow (minimum 0.03 square meters per minute) to ensure the heat generated by the machine is sufficiently dissipated.
-
AC Distance: Air conditioning vents should be at least 3 meters away from the printer, and the airflow direction must not point directly at the machine.
-
Environmental Hazards: Ensure the workspace is free from the following:
-
Dust
-
Smoke
-
Steam/Vapor
-
Operational Space and Placement Specifications
Notice: Incorrect placement of the White Wax machine and oxygen generator may lead to damage or negatively affect print quality. Please strictly follow these installation space specifications.
Platform Requirements
The machine must be placed on a platform that is stable, firm, and level.
Minimum Clearance for Maintenance and Heat Dissipation
-
Rear: At least 35 cm (13.78 in).
-
Sides (Left/Right): At least 60 cm (23.62 in).
-
Above: At least 120 cm (47.24 in) from the tabletop.
Oxygen Generator Space Requirements
-
The generator can be placed on the floor near the White Wax machine and connected via an air tube.
-
Ensure at least 20 cm of clearance on all sides (front, back, left, and right) for air intake and heat dissipation to ensure a stable oxygen supply.
Electrical Requirements
In areas with unstable power supply, it is recommended to use a UPS (Uninterruptible Power Supply) to protect the machine.
To ensure stable operation, all the following electrical requirements must be met:
-
Standard municipal power supply.
-
Do not connect any additional equipment to the same power circuit as the machine.
-
White Wax Machine: Requires 220V voltage and a current of no less than 8A.
-
Oxygen Generator: Requires 220V voltage and a current of no less than 5A.
-
Connect the White Wax machine and the oxygen generator to separate surge protectors or individual UPS units.